WE PDW M4 Open Bolt Feed

Page 2 of 2 Previous  1, 2

View previous topic View next topic Go down

Re: WE PDW M4 Open Bolt Feed

Post by Howie on 27th June 2011, 10:01 am

Okay guys,
Now after last weekend, it's Appearred that the Spring for the Housing that attaches too the nozzle was weak causing kinks in the spring which fail on three of four Nozzle housings, so went to Hall's hardware store and dig through the springs and found the #16U Extension Spring 2" length 3/16" outer Dia #20 wire gauge which is similar to what was install. Remove the Housing Pin holding spring then remove the smaller pin holding the Nozzle, other side of spring and plastic valve insert, Now the NPAS valve has an spring in front so watch how it seperates to ensure installation goes back correctly. Pictures to follow soon. Also results from testing Very Happy
avatar
Howie
Your the Man
Your the Man

Posts : 1945
Join date : 2010-03-07
Age : 42
Location : Milton Florida

Back to top Go down

Re: WE PDW M4 Open Bolt Feed

Post by Che Chuy on 27th June 2011, 12:10 pm

This thread should be renamed: Howie's How-To Scratch build a GBBR

_________________
Milsim: The uncanny valley that divides the real from the realistic.
[You must be registered and logged in to see this image.]
avatar
Che Chuy
Wayward Admin

Posts : 1634
Join date : 2010-03-31
Age : 46
Location : Bradenton, Fl.

Back to top Go down

Re: WE PDW M4 Open Bolt Feed

Post by Howie on 27th June 2011, 12:44 pm

Okay Guys,
It was successful, shot through 5 mags and no hang ups with the nozzle, good to Go!

[You must be registered and logged in to see this image.]
Everything apart. minus the valve assembly, it is still in the foward Nozzle tip

[You must be registered and logged in to see this image.]
Nozzle put back together where you can see the Spring sticking out

[You must be registered and logged in to see this image.]
Complete Nozzle housing back together
avatar
Howie
Your the Man
Your the Man

Posts : 1945
Join date : 2010-03-07
Age : 42
Location : Milton Florida

Back to top Go down

Re: WE PDW M4 Open Bolt Feed

Post by Nos on 27th June 2011, 5:02 pm

Your right it should be renamed to howies how to build pdw from scratch haha

_________________
Trevor Lemmon
[You must be registered and logged in to see this image.]
avatar
Nos
Joe High Caps
Joe High Caps

Posts : 256
Join date : 2011-05-26
Age : 19

Back to top Go down

Re: WE PDW M4 Open Bolt Feed

Post by Howie on 1st August 2011, 4:50 pm

Okay guys after all the shooting of B.B.'s through the Tan PDW, the Valve Striker Assembly finally Broke, lucking that Allout had a spare one . Now good to go for a few more thousand rounds
avatar
Howie
Your the Man
Your the Man

Posts : 1945
Join date : 2010-03-07
Age : 42
Location : Milton Florida

Back to top Go down

WE PDW M4 Open Bolt Feed

Post by g-ant1991 on 2nd August 2011, 12:23 am

The bolt is actually pretty similar to my bolt on my WE M14. Have you had any plastic pieces break off of the bolt assembly and jam it? I did but I could never figure out where they came from and when i put it back together it shot like new..... Question
avatar
g-ant1991
Meat Puppet
Meat Puppet

Posts : 28
Join date : 2011-05-31
Age : 26

Back to top Go down

Re: WE PDW M4 Open Bolt Feed

Post by Sponsored content


Sponsored content


Back to top Go down

Page 2 of 2 Previous  1, 2

View previous topic View next topic Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum